(navigation image)
Home American Libraries | Canadian Libraries | Universal Library | Community Texts | Project Gutenberg | Children's Library | Biodiversity Heritage Library | Additional Collections
Search: Advanced Search
Anonymous User (login or join us)
Upload
See other formats

Full text of "PSP 3000 Repair Manual"

Installing PSP 3000 Trigger Buttons 



iiixit 



Installing PSP 3000 Trigger Buttons 



Tools used in this guide 

• Phillips #1 Screwdriver (1) 

• Spudqer (1) 



Steps for replacing the trigger buttons for the Sony PSP-3000. 



© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 9 



Installing PSP 3000 Trigger Buttons 




Step 1 - Battery 

• Start on the back of the device. This is where the 
battery and the battery cover are located. 




Step 2 

• The battery door is located on the left side when 
looking at the PSP from the back. Lift open the battery 
door to reveal the battery. Remove the battery cover. 

• Using your finger, pry up the top edge of the battery. 
Continue to pull the top edge until the bottom of the 
battery is free. 

• Remove the battery. 



©2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 2 of 9 



Installing PSP 3000 Trigger Buttons 




Step 3 - Casing 

• Using a spudger or fingernail, peel back the warranty 
sticker that is behind the battery. 



^Hfc \ 


1 







step 4 

• Unscrew all four screws from the back of the PSP. 

• Two from behind the battery. 

• Two on the right side of the PSP. 



©2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 3 of 9 



Installing PSP 3000 Trigger Buttons 




Steps 

• Unscrew two screws from the top of the PSP. 




Step 6 

• Remove a single screw from the bottom surface of the 
PSP. 



© 2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 4 of 9 



Installing PSP 3000 Trigger Buttons 




Step? 

• Starting from the 'R' trigger, slide the spudger in 
between the outer casing the the PSP, and gently pry 
off the casing. 

• Remove the front casing completely. 




Step 8 - LCD Screen 

• Push the homebar to the right to release the tab on the 
right side of the LCD screen. 

• DO NOT completely remove the homebar, 
as it is still connected by ribbon cables. 



A 



© 2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 5 of 9 



Installing PSP 3000 Trigger Buttons 




Step 9 

• Slowly begin to lift the LCD screen off the PSP from the 
top edge. 

• Again, the LCD screen is attached by ribbon 
cables, so do not remove it completely. 



• Orientation of PSP flipped in photo 







Step 10 

• Using a spudger or fingernail, flip the small brown locks 
on the four ribbon cable connectors up. 

• Pull all four ribbon cables out, and remove the LCD 
screen and homebar from the PSP. 



©2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 6 of 9 



Installing PSP 3000 Trigger Buttons 




Step 11 

• Remove the metal tab the lies above the LCD. 

• Upon reassembly, make note that the 
stamped lettering faces down, and the large 
tab fits just above the motherboard to the 
right of the left trigger. 



}^ 




step 12 - Trigger Buttons 

• Remove the screw securing 'L' trigger to the PSP. 




Step 13 

• Remove the white plastic piece that holds the 'L' trigger 
in place. 



© 2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 7 of 9 



Installing PSP 3000 Trigger Buttons 




Step 14 

• Remove the 'L' trigger from the PSP. 




1 Step 15 

• Remove the screw securing 'R' trigger. 




Step 16 

• Remove the white plastic piece that holds the 'R' trigger 
in place. 



© 2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 8 of 9 



Installing PSP 3000 Trigger Buttons 




Step 17 

• Remove the 'R' trigger from the PSP. 



To reassemble your device, follow these instructions in reverse order. 



This document was last generated on Dec 14, 2010. 



© 2010 iFixit — CC BY-NC-SA 



www.iFixit.com 



Page 9 of 9